PCO - Testing of Coating (17 articles)
Prev[1]Next
Show: Grid Sort by:
PDEF CSP Concrete Surface Profile Chips (set of 10) Set of 10 Concrete Surface Profile Chips (CSP 1 - 10)

The International Concrete Repair Institute (ICRI) produces 10 distinct concrete profiles formed by various surface preparation methods. Each profile carries a CSP number ranging from CSP 1 (nearly flat) to CSP 10 (very rough; amplitude greater than ¼” [6 mm]).

These chips are designed as a visual and tactile comparator for identifying the degree of surface roughness. The user compares prepared concrete to the CSP chips and reports the chip number that most closely resembles the surface. Many jobs will specify the type of surface preparation required.

The ICRI CSP Chips are approximately 16 square inches (3.5” x 4.5”) and are designed to replicate 10 surface profiles shown below.

Without Technical Guideline (no. 310.2R-2013) Selecting and Specifying Concrete Surface Preparation for Sealers, Coatings, Polymer Overlays, and Concrete Repairs prepared by ICRI.

Look-up Table (Conversion of ICRI Panels to mils)
Description                ICRI CSP No.       Digital Depth Micrometer / ASTM D8271 (mils)* Learn More
Acid-etched                       1                             6 ± 2
Grinding                            2                             6 +/- 2
Light Shotblast                   3                             11 ± 2
Light Scarication                4                             15 ± 2
Medium Shotblast              5                            16 ± 2
Medium Scarification          6                            37 ± 4
Heavy Abrasive Blast           7                            48 ± 4
Scabbled/Surface Retarder   8                     Not measured
Heavy Scarification              9                      Not measured
Handheld Concrete Breaker/Abrasive Blast 
Cleaned; or High-Pressure Water Jetting
                                         10                  Not measured

*Average of 15 readings, based on the data generated in this study PDEF CSP
PDEF CSP
v
PDEF CSPTG Concrete Surface Profile Chips with Technical Guide (set of 10) Concrete Surface Profile Chips with Technical Guide (set of 10)
Set of 10 Concrete Surface Profile Chips (CSP 1 - 10)
Technical Guideline (no. 310.2R-2013)
The guide provides owners, specifiers, contractors, and manufacturers with the information required to select and specify the methods for preparing concrete surfaces prior to the application of a protective system or repair material.

The International Concrete Repair Institute (ICRI) produces 10 distinct concrete profiles formed by various surface preparation methods. Each profile carries a CSP number ranging from CSP 1 (nearly flat) to CSP 10 (very rough; amplitude greater than ¼” [6 mm]).

These chips are designed as a visual and tactile comparator for identifying the degree of surface roughness. The user compares prepared concrete to the CSP chips and reports the chip number that most closely resembles the surface. Many jobs will specify the type of surface preparation required.

The ICRI CSP Chips are approximately 16 square inches (3.5” x 4.5”) and are designed to replicate 10 surface profiles shown below.

Available with or without Technical Guideline (no. 310.2R-2013) Selecting and Specifying Concrete Surface Preparation for Sealers, Coatings, Polymer Overlays, and Concrete Repairs prepared by ICRI.

Look-up Table (Conversion of ICRI Panels to mils)
Description                ICRI CSP No.       Digital Depth Micrometer / ASTM D8271 (mils)* Learn More
Acid-etched                       1                             6 ± 2
Grinding                            2                             6 +/- 2
Light Shotblast                   3                             11 ± 2
Light Scarication                4                             15 ± 2
Medium Shotblast              5                            16 ± 2
Medium Scarification          6                            37 ± 4
Heavy Abrasive Blast           7                            48 ± 4
Scabbled/Surface Retarder   8                     Not measured
Heavy Scarification              9                      Not measured
Handheld Concrete Breaker/Abrasive Blast 
Cleaned; or High-Pressure Water Jetting
                                         10                  Not measured

*Average of 15 readings, based on the data generated in this study PDEF CSPTG
PDEF CSPTG
v
PDEF PC4 DeFelsko Powder Comb PC4 DeFelsko Powder Comb PC4
Model 4 (µm)

Teeth Height: 75, 150, 225, 300 PC1 t 6
PDEF PC4
v
PDEF PC5 DeFelsko Powder Comb PC5 DeFelsko Powder Comb PC5
Model 5 (µm)

Teeth Height: 250, 375, 500, 625 PC1 t 6
PDEF PC5
v
PDEF PC6 DeFelsko Powder Comb PC6 DeFelsko Powder Comb PC6
Model 6 (µm)

Teeth Height: 500, 750, 1000, 1250 PC1 t 6
PDEF PC6
v
PDEF STDS3 DeFelsko Verifcation Standard Coating Thickness Certif Coated Metal Plates S3 DeFelsko Verifcation Standard Coating Thickness Certif Coated Metal Plates S3

Certified coated metal plates and polystyrene blocks are ideal for verifying the accuracy and operation of coating thickness gages and are an important component in fulfilling both ISO and in-house quality control requirements.

Many organizations require verification of gage accuracy at the test site each time a coating thickness gage is put into service and at frequent intervals during use. Ideal for this purpose, DeFelsko certified coating thickness standards have measured values traceable to a National Metrology Institution.

Used to verify the accuracy and operation of any Type 1 (mechanical) and Type 2 (electronic) magnetic, eddy-current or ultrasonic coating thickness gage
Ideal for use in the calibration lab, in the field or on the factory floor
Standards with steel or aluminum substrates consist of 4 plates mounted in a protective binder
Polystyrene thickness standards consist of 4 blocks supplied in a rugged acrylic storage box
Individually serialized for traceability to NIST or PTB - includes a Certificate of Calibration
Certified and labeled in both Metric and Imperial units
Zero Plates available for both Certified Coated Metal Plates and Certified Polystyrene Blocks.
PDEF STDS3
v
KT LZ990 LZ990  Kett Portable Coating Thickness Gauge LZ990  Kett Portable Coating Thickness Gauge
For non-magnetic coatings on magnetic or non-magnetic metal substrates KT LZ990
KT LZ990
v
PDEF200ADV Positector packet adv coating beton tot 7600µm Positector 200
with Advanced Model and D-Probe
 PDEF200ADV
PDEF200ADV
v
PDEF200ADC Positector packet adv coating concrete 3800µm Positector 200 C3
with Advanced Model and C3-Probe
 PDEF 200ADC
PDEF200ADC
v
PDEF200B Positector packet stnd coating plastc,wood, ... to 1000µm Positector 200
wiè Standard Model and C-Probe
 PDEF200B.jpg
PDEF200B
v
PDEF DFTC-C PosiTest DFT Combo non-magnetic coatings on steel, aluminium, brass, etc PosiTest DFT Combo non-magnetic coatings on steel, aluminium, brass, etc.


Features
- Fast, repeatable measurements — 60+ readings per minute
- Ready to measure—no adjustment required for most applications
- Zero or 1 Point Calibration Adjustment for complex applications
- Onscreen averaging for up to 99 readings
- Strong, wear-resistant, ruby-tipped probe
- V-groove in probe for positioning on cylindrical parts
- High contrast color display
- Adjustable display brightness for optimal visibility in any environment
 -Auto rotating display with lock to prevent unintended rotations
- Simple, icon based menu
- Handy RESET feature when no zero reference is available
- Mils/microns switchable
- Built-in wrist strap for added convenience and safety
- Two year warranty

ALL GAGES COME COMPLETE
with wrist strap, precision plastic shims, hard shell storage case, 2 AAA alkaline batteries, instructions, Long Form
Certificate of Calibration traceable to PTB, two year warranty.

OPTIONS
Pouch with belt clip protects your PosiTest DFT while keeping it within easy reach
Coating Thickness Standards to fulfill both ISO and in-house quality control requirements

SIZE: 108 x 43 x 20 mm (4.25" x 1.7" x 0.8")
WEIGHT: 54 g (1.9 oz.) PDEF DFTF-C
PDEF DFTC-C
v
PDEF DFTF-C PosiTest DFT Ferrous non-magnetic coatings on steel PosiTest DFT Ferrous non-magnetic coatings on steel

Features
- Fast, repeatable measurements — 60+ readings per minute
- Ready to measure—no adjustment required for most applications
- Zero or 1 Point Calibration Adjustment for complex applications
- Onscreen averaging for up to 99 readings
- Strong, wear-resistant, ruby-tipped probe
- V-groove in probe for positioning on cylindrical parts
- High contrast color display
- Adjustable display brightness for optimal visibility in any environment
 -Auto rotating display with lock to prevent unintended rotations
- Simple, icon based menu
- Handy RESET feature when no zero reference is available
- Mils/microns switchable
- Built-in wrist strap for added convenience and safety
- Two year warranty

ALL GAGES COME COMPLETE
with wrist strap, precision plastic shims, hard shell storage case, 2 AAA alkaline batteries, instructions, Long Form
Certificate of Calibration traceable to PTB, two year warranty.

OPTIONS
Pouch with belt clip protects your PosiTest DFT while keeping it within easy reach
Coating Thickness Standards to fulfill both ISO and in-house quality control requirements

SIZE: 108 x 43 x 20 mm (4.25" x 1.7" x 0.8")
WEIGHT: 54 g (1.9 oz.) PDEF DFTF-C
PDEF DFTF-C
v
PDEF FM PosiTest FM (banane) Coating Thickness measurement PosiTest FM (banane) Coating Thickness measurement

Magnetic Coating Thickness Gages for Non-Magnetic Coatings on Steel
PosiTest magnetic pull-off thickness gage (banana gauge) for the non-destructive measurement of non-magnetic coatings (paint, enamel, galvanizing, metalizing, plating, etc.) on steel.
 Highly wear resistant Carbide Probe for longest life and continuous accuracy
 Extra rugged housing, not affected by mechanical shock, water, acid or solvents
 Unique overall design, fully supported, positive positioning, no pivoting tendencies during measurement
 Positive visual and audible indicators to designate when thickness reading is established
 “V” grooves in probe housing and gage base allow correct positioning on cylindrical objects 
 Certificate of Calibration showing traceability to PTB included (Long Form)
Conforms to ASTM D7091/B499, ISO 2808 and others PDEF FM
PDEF FM
v
PDEF SPG OS3 PosiTestor SPG Surface Profile Adv Body + Cabled Probe outside diameters PosiTestor SPG Surface Profile Advanced Body + Cabled Probe outside diameters PDEF SPG OS3
PDEF SPG OS3
v
PDEF SPG TS3 PosiTestor SPG Surface Profile Advanced Body + Probe on Concrete PosiTestor SPG Surface Profile Advanced Body + Probe on Concrete SPG TS1
PDEF SPG TS3
v
PDEF SPG1 PosiTestor SPG Surface Profile Standard Body + Probe PosiTestor SPG Surface Profile Standard Body + Probe SPG1-E
PDEF SPG1
v
PDEF SPG TS1 PosiTestor SPG TS1 Standard PosiTestor SPG TS1 Standard 
Surface Profile Gage - Concrete SPG TS1
PDEF SPG TS1
v
Prev[1]Next